Light steel structures are mainly composed of steel beams, steel columns, steel trusses and other components, which are usually connected by welding, bolts or rivets. Strict treatment is required before welding, and there are many difficulties in the welding process.

　　1. 焊道應將基材與坡口內墊板的連接處密封，然后逐層焊接，直至坡口填滿。每道焊縫焊接后，應清除焊渣和飛濺。

　　1. The joint between the base material and the base plate in the groove shall be sealed in the weld bead, and then welded layer by layer until the groove is filled. After each weld is welded, the welding slag and spatter shall be removed.

　　2、輕鋼結構焊接的一般順序是:焊前檢查、預熱除銹、焊墊和電弧板、焊接、檢查。

　　2. The general welding sequence of light steel structure is: pre welding inspection, preheating and derusting, welding pad and arc plate, welding and inspection.

　　3.焊接前應檢查坡口角度、鈍邊、間隙及口數是否正確。溝槽內、兩側銹斑、油漬、氧化鐵皮等應清洗干凈。

　　3. Before welding, check whether groove angle, blunt edge, clearance and number of openings are correct. Rust spots, oil stains, oxide scales, etc. inside and on both sides of the trench shall be cleaned.

　　4. 預熱:焊接前，用氣焊或?qū)Ｓ酶駯艠寣⒒脑谄驴诩捌鋬蓚?cè)100mm范圍內均勻加熱，并用表面溫度計測量溫度，防止溫度不符合要求或局部表面氧化、預熱溫度。

　　4. Preheating: before welding, use gas welding or special grid gun to evenly heat the base material within 100mm of groove and both sides, and use surface thermometer to measure the temperature to prevent the temperature from not meeting the requirements or local surface oxidation and preheating temperature.

　　5、重新檢查預熱溫度，如溫度不夠應重新加熱以滿足要求。

　　5. Recheck the preheating temperature. If the temperature is not enough, reheat it to meet the requirements.

　　鋼結構在焊接過程中如遇雨、下雪應停止焊接，且焊接構件周圍及以上應有防風罩、雨棚，當環境溫度低于零時，應按規定采取預熱和后加熱措施。

　　In case of rain and snow during the welding process of steel structure, the welding shall be stopped, and wind shield and canopy shall be set around and above the welding components. When the ambient temperature is lower than zero, preheating and post heating measures shall be taken as required.

　　以上就是對濟南輕型鋼結構在焊接過程中都有哪些困難的詳細介紹，想要了解更多請點擊官網http://jmxiantai.com
The above is a detailed introduction to the difficulties in the welding process of Jinan light steel structure. For more information, please click http://jmxiantai.com